advice

[rhino 2]

Yes, all started when I install the new batt.

Maybe when I install the new batt I did a wrong connection or miss something.

Electronics ;101… Go back to the last thing you Touched before the problem started you might have left a wire disconnected when You installed the battery?…

Also even with a new battery it is good Practice to fully charge the battery yourself before you install it.. even though the salesman will say the battery comes fully charged.!

 

[Jack Klarich]

Electronics ;101… Go back to the last thing you Touched before the problem started you might have left a wire disconnected when You installed the battery?…

Also even with a new battery it is good Practice to fully charge the battery yourself before you install it.. even though the salesman will say the battery comes fully charged.!

#1 on Bobs post

I would also strongly encourage you to dis connect the LED system to see how the tail light and brake lights behave

Narrow the systems down to help you isolate what the problem area is

If you have a volt meter measure your voltage before you start, a fully charged battery is a plus, make sure the connections #@ the battery are clean and tight

You should see 12.7 volts in a fully charged battery

 

[solwiso]

Assistance

Hello, good afternoon

Hope you having a good Saturday.

I'm back again here in the garage. I went out and bought Socket ASY, T-Light?DOM. Now the lights in the rear works. The turn signal works. But having problem with the break. When I break from the Handlebar, it does not work. When I press on the pedal break, will not light up. But when I release the Padel break the lights turn off and back again.

 

[solwiso]

Assistance

I did disconnect the LEDS lights. Rear lights working but still no break lights

 

[Jack Klarich]

I did disconnect the LEDS lights. Rear lights working but still no break lights

Run another scan of your ECM to see if you have any codes, if your brake lights are not working you could have a code

 

[Jack Klarich]

Hello, good afternoon

Hope you having a good Saturday.

I'm back again here in the garage. I went out and bought Socket ASY, T-Light?DOM. Now the lights in the rear works. The turn signal works. But having problem with the break. When I break from the Handlebar, it does not work. When I press on the pedal break, will not light up. But when I release the Padel break the lights turn off and back again.

This sounds backwards to me, it sounds like your brake lights are on, but when you apply the brakes they turn off?

Are the rear bulbs in correctly? Do your bulbs look like this

 

[solwiso]

Yes, the lights look the one you send

 

[solwiso]

yes the light look like the picture

 

[solwiso]

Assistance

I again check all fuze and they all are functional

 

[solwiso]

Assistance

I re did DTC and have the same codes as before.

BCM

B2123

B2124

B2151

B2271

SPDO

B1210

Now my question is,, should I deleted the codes from then last time i did DTC ?

 

[Jack Klarich]

I re did DTC and have the same codes as before.

BCM

B2123

B2124

B2151

B2271

SPDO

B1210

Now my question is,, should I deleted the codes from then last time i did DTC ?

Yes, clear them

I bet your cruise control does not work if your brake lights are not working right

Clear the codes and rescan

You can check that here

1. bike off, run/stop to run

2. push set/resume to set and hold.

3 with cruise on/off switch to on, turn on bike

4. cruise indicator light should be green, release set switch, light should turn red.

5. push to resume and release, light should turn green then red

6. push throttle closed and release, light should turn green then red

7. push rear brake pedal and release, light should turn green then red

8. pull front brake lever, light should turn green then red

9. on models with a clutch/neutral starter lockout, pull clutch lever, light should turn green then red

whichever switch does not turn the light green, is your bad one.

if light will not turn green at all and you have followed ALL directions and tried multiple times, your set/resume switch is bad.

If light stays green even after releasing set switch, one of the dropout switches is stuck closed, usually the roll off throttle switch. unplug this and try again.

make sure brake light will not turn on without using brakes (wobbly brake lever, stuck rear brake light switch etc.)

 

[solwiso]

Assistance

Cruise control works.

deleted the old DTC codes. Started the bike then turn off.

Check the DTC, The DTC has no codes.

 

[Jack Klarich]

Cruise control works.

deleted the old DTC codes. Started the bike then turn off.

Check the DTC, The DTC has no codes.

Good, your brake lights must be working if the cruise checks out and you have NO codes, confirm this

 

[solwiso]

Assistance

Still no codes..

I check again for the cruise control,,now it will not work

 

[Jack Klarich]

Still no codes..

I check again for the cruise control,,now it will not work

You have a wiring problem some where, the cruise will not work if the brake lights do not work, pull the fuses 1 at a time and look carefully at them. Electrical problems can be a very hard thing to fix with out starting all over

Who did the install of your LED light set?

Is there any extra wires running under your seat to the rear of the trike?

Where exactly do you live in Jacksonville?

If you are close to me I can look at it for you

 

[solwiso]

Assistance

The installer was done one of the businesses in Bike week in Daltona.

The only wire to the rear is for my amp for the speakers.

I live near the Berlin Road, 13342 cedar hammock way. close to the Rivercity Town center.

 

[solwiso]

Assistance

Other wire extra connected to the batt is: the LED and the Bluetooth for the speakers.

 

[Jack Klarich]

The installer was done one of the businesses in Bike week in Daltona.

The only wire to the rear is for my amp for the speakers.

I live near the Berlin Road, 13342 cedar hammock way. close to the Rivercity Town center.

So to be clear, did you short out or connect the battery backward by accident?

All lights worked prior to new battery?

Did you get a warranty on the install of your LED lights?

 

[Jack Klarich]

Other wire extra connected to the batt is: the LED and the Bluetooth for the speakers.

Disconnect all extra wires at the battery for now, to narrow problems down

recheck the brake lights and cruise control

 

[solwiso]

Assistance

No,, it was not connected the batt backward. The batt is connected right.

Light was an issue before the new batt.

Yes I do have warranty for the LED.

 

[solwiso]

Assistance

Wish I could send you pic of the connection on the batt.

But this forum will not let post pic

 

[Jack Klarich]

No,, it was not connected the batt backward. The batt is connected right.

Light was an issue before the new batt.

Yes I do have warranty for the LED.

I have to go out to dinner with my grand daughter, I will check back here when I get back

I am running out of ideas without having your trike here in front of me

 

[solwiso]

Assistance

Thats great,, Have a good out dinner with your daughter.. Enjoy.

I need as well take care my dog and set up dinner for me..

Chat later

Stay safe'

 

[solwiso]

Assistance

Good afternoon.

I will be on the road riding the trike. Need to get several patches on my jackets. If you have time today Here is my number 904-548-7532. If you have any other idea that i can work on the bike.

 

[Jack Klarich]

Good afternoon.

I will be on the road riding the trike. Need to get several patches on my jackets. If you have time today Here is my number 904-548-7532. If you have any other idea that i can work on the bike.

OK, check open Road Leathers on Beach Blvd, they do sewing @ a great price

If you have GPS, stop by my house 3566 Hampton Glen Place, 32257 , I can look at your light problem

I have test lights and volt meters 904-304-3545 Jack

 

[solwiso]

Assistance

Road Leathers on Beach Blvd is the place where i take care of my patches.

Soon I finish here I will come around your location

 

[Jack Klarich]

Road Leathers on Beach Blvd is the place where i take care of my patches.

Soon I finish here I will come around your location

OK

 

[consitter]

???

How did it turn out??

 

[Jack Klarich]

???

How did it turn out??

His Freewheeler has a bad rear brake light switch, I found the code today. He has an extended warranty @ the same dealer I buy from here in Jax Fl. He will take it in and it should be good to go

We had a good visit today and plan on doing some riding soon

 

[consitter]

His Freewheeler has a bad rear brake light switch, I found the code today. He has an extended warranty @ the same dealer I buy from here in Jax Fl. He will take it in and it should be good to go

We had a good visit today and plan on doing some riding soon

Glad to hear things turned out well...glad he didn't rob you...:laugh: